![]() ![]() The batteries are annoying, they barely fit, and the slightest bump and they pop out of place. Luckily my kitten has always been the type to sleep through the whole night. So loud it would wake me up if I napped, but my job got so busy that I learned to sleep through it, so I didn’t complain too much. I wish there was a test button, where it dispenses food upon pressing, because having to program it to measure how much food came out was irritating. I didn’t think it was too bad at first, programming was indeed annoying, but not as annoying as my kitten. Then replace batteries and re-program feeder. If full function is not returned remove batteries for 5 minutes. In the unlikely event that the display becomes non-responsive, wait 3 minutes before attempting to pressĪny buttons. Reassemble the feeder and press the ‘TIME’ button to stop the display flashing and resume normal.Also consider the use of a different feed that may be less prone to blockage. NOTE: Before reassembling the feeder, we recommend the batteries are replaced. Rotate feeding mechanism by hand as shown in Fig.Is unable to clear the blockage, the whole LCD screen will flash. The use of a CAT MATE fountain for fresh water sources is also recommended.Your feeder has been extensively tested with a variety of dry foods but in the unlikely event that the feederīecomes jammed, the base unit is programmed with an automatic clearing function. Cats, particularly kittens, should not be left alone for long periods without anyone constantly checking that all is well. For cats, in particularĭo not fail to make suitable toilet arrangements for it while leaving your cat. We suggest, however, that you ensure the proper functioning with your cat. Consequently, it can provide you with stable use for several years. Your C500 feeder is made from materials of the highest quality and is assembled to follow strict quality requirements. ![]() Then click the UP and DOWN arrow keys together until you cancel the configuration. Before meal time flashes, press and hold the ADJ/SET button. Change it with the UP and DOWN arrow keys.ģ.3 Use the UP/DOWN arrow buttons to show the appropriate meal time frame to cancel the meal time setting. Click ADJ/SET to save the settings.ģ.2 Press the ADJ/SET button and the minute figure flashes. To plan the hours for MEAL 1, use the UP and DOWN arrow keys. Push and hold the ADJ/SET button for 3 seconds until the 1 hour MEAL starts blinking. You should set yourself up to 4 meals a day.įor your pets, set the appropriate daily meal times as follows:ģ.1 To move the highlight frame to MEAL 1, press the UP or DOWN arrow keys. You would need to set the times for MEAL 1 and MEAL 2 to allow feeding for up to 2 days if you require 2 meals per day. For example, you only need to set the time for MEAL 1 to allow feeding for up to 4 days if you require one meal a day. Once you have set the necessary meal times, the C500 feeder will automatically serve meals at the same time(s) per day. Adjust using the arrow buttons UP and DOWN. To change the clock to the correct hour, click the UP and DOWN arrow keys.Ģ.2 Press the ADJ/SET button and it will flash the minute number. Press and hold the ADJ/SET button for 5 seconds before the hour figure begins to light, to set the clock. If a button is not pressed within 30 seconds at any point during the setting, all digits will stop blinking and any changes made will return to default/previous settings.Ģ.1 Shift the highlight frame if necessary to outline the clock display using the UP arrow button. Click and hold the DOWN arrow button until the format changes within 5 seconds. NOTE: To adjust the clock format from 24 hours to 12 hours (AM/PM), press and hold the ADJ/SET button. You can use all common batteries, including rechargeable and 1.5v lithium batteries, but only with regular alkaline batteries will the low battery indicator function properly. Substitute the cover for the battery.Īlkaline batteries of good quality can usually last for around 12 months. Using the orientation symbols indicated on the inside of the compartment to insert 3 x AA batteries. By releasing the retaining clip, raise the food bowl off the feeder base and remove the battery cover.Ģ. By pushing down the lid and pressing in the sprung clips on both sides, detach the feeder lid.
0 Comments
Leave a Reply. |